MSI laptop screens & parts

A replacement touch screen compatible with the MSI Other VENTURE A14 A3HM SERIES, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI VENTURE A14 A3HM SERIES and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other VENTURE A14 A3HMTG, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI VENTURE A14 A3HMTG and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other VENTURE A14 A3HMTG-019US, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI VENTURE A14 A3HMTG-019US and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UET-411HK, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UET-411HK and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UET-412HK, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UET-412HK and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UET-424CZ, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UET-424CZ and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UET-430RU, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UET-430RU and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UET-447VN, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UET-447VN and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UET-471, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UET-471 and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UET-478JP, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UET-478JP and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UET-491PL, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UET-491PL and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UET-492RU, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UET-492RU and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UET-494CA, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UET-494CA and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UGT SERIES, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UGT SERIES and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UGT-004NL, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UGT-004NL and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UGT-005BE, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UGT-005BE and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UGT-043IT, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UGT-043IT and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UGT-068PL, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UGT-068PL and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UGT-077AU, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UGT-077AU and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UGT-229FR, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UGT-229FR and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UGT-410HK, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UGT-410HK and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UGT-423CZ, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UGT-423CZ and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UGT-429RU, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UGT-429RU and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the MSI Other CREATOR 15 A10UGT-465, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your MSI CREATOR 15 A10UGT-465 and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock