HP PAVILION 14-CD laptop screens & parts

A replacement battery compatible with the HP PAVILION 14-CD SERIES, supplied new. If your machine shuts down early, reports a swollen or "service" battery, or only runs on mains power, a new battery is the fix — and on most modern laptops it is a straightforward one. Before you order Specifications — compare the voltage, capacity and battery part code printed on your original with this listing, and check the model label on the underside of your laptop against the models named in the title. Batteries are shaped for their series and do not carry across between them. Variations — where the listing offers more than one option (capacity or grade), choose the variation that corresponds to what your machine came with. Images — check the photos for the connector type and the outline of the battery; both need to correspond to your original. Unsure? — send us a photo of the label on your existing battery together with your HP 14-CD SERIES and we will confirm compatibility. Swollen battery? — stop using the laptop, do not press on the case or trackpad, and replace it promptly. A swollen battery only gets worse. Fitting and battery care Power off and unplug before opening the base. Disconnect the old battery's connector first, and reconnect the new one last. Give the new battery a full charge before its first run on battery power. Recycle the old one: in Australia, any B-cycle drop-off point (most major supermarkets have one) takes laptop batteries free of charge. Never put a lithium battery in the bin. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Part: Battery

Stock: Out of Stock

A replacement internal part compatible with the HP PAVILION 14-CD SERIES. The title states what this part is — a webcam module, hinge set, sensor board, bracket or similar small assembly — and the photos show the unit supplied. Before you order Specifications — small parts are shaped for their series. Compare the model label on the underside of your machine with the models in the title, and check any details the title gives, such as connector type or a note like "no program" where a board needs software pairing. Variations — where the listing offers more than one option (left and right hinges, for example, or different revisions), choose the variation that corresponds to the part you are replacing. Images — compare the photos with your part: connector position, cable length and mounting holes are what decide whether it fits. Unsure? — the part number printed on your original is the most reliable reference. Send it to us, or a photo of the part, with your HP 14-CD SERIES and we will confirm compatibility. Fitting These parts are fiddly rather than difficult: small connectors, short cables and screws that like to wander. Disconnect the battery first, work over a tray, and never fold a ribbon cable sharply. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Part: Part

Stock: Out of Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD L20552-001: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD L20552-001, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD L20553-001: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD L20553-001, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD L20555-001: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD L20555-001, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD L20556-001: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD L20556-001, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD L20558-001: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD L20558-001, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD L20559-001: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD L20559-001, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD0001DX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD0001DX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD0003DX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD0003DX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD0005DX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD0005DX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD0011CA: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD0011CA, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD0505SA: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD0505SA, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD0520SA: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD0520SA, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP PAVILION X360 14-CD0522SA: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP X360 14-CD0522SA, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0000: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0000, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0000TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0000TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0000TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0000TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0001TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0001TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0001TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0001TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0002TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0002TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0002TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0002TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0003TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0003TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0004TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0004TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0004TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0004TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0005TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0005TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0005TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0005TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0006TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0006TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0006TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0006TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0007CA: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0007CA, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0007TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0007TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0008TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0008TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0008TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0008TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0009TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0009TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0010TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0010TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0010TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0010TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0011NR: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0011NR, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0011TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0011TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0012TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0012TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0012TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0012TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0013TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0013TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0014TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0014TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0015TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0015TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0015TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0015TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0016TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0016TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0016TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0016TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0017TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0017TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0018TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0018TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0018TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0018TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0019TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0019TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0019TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0019TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0020TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0020TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0020TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0020TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0021TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0021TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0022TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0022TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0022TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0022TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0023TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0023TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0024TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0024TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0026TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0026TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0027TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0027TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0027TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0027TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0028TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0028TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0028TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0028TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0029TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0029TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0030TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0030TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0030TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0030TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0031TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0031TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0031TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0031TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0032TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0032TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0032TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0032TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0033TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0033TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0033TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0033TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0034TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0034TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0034TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0034TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0035TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0035TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0036TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0036TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0037TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0037TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0038TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0038TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0038TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0038TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0039TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0039TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0040TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0040TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0041TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0041TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0041TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0041TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0042TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0042TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0042TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0042TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0043TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0043TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0043TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0043TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0044TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0044TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0044TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0044TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0045TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0045TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0045TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0045TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0046TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0046TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0047TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0047TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: In Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0048TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0048TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0048TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0048TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0049TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0049TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0049TX: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0049TX, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0052TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0052TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock

A complete touch screen assembly compatible with the HP Pavilion x360 14-CD0053TU: the LCD panel and the glass touch digitizer supplied as one factory-bonded unit. Where the title mentions a frame or bezel, the assembly ships pre-mounted in it. Why replace the whole assembly? On touch laptops the glass is bonded to the LCD under pressure at the factory. Prising cracked glass off an intact LCD is slow, risky work that often destroys the panel underneath — which is why repairers fit the bonded assembly instead. One part, one swap, and both the picture and the touch layer are new. Before you order Manufacturers sell the same model with touch and non-touch lids, in more than one resolution and often in more than one bezel style, so please compare this assembly with your machine: Specifications — confirm your machine is the touch version, then compare the resolution, refresh rate and connectors with your original before ordering. Variations — where the listing offers options such as with or without frame, or different bezel colours, choose the variation that suits your lid; the frame is not interchangeable between revisions. Images — compare the photos with your machine's bezel shape, hinge covers and camera cut-out; these details change between revisions of the same series. Want a second opinion? — send us a photo of your lid and the code on the rear of the original panel, along with your HP 14-CD0053TU, and we will confirm compatibility. Fitting An assembly swap is usually easier than a bare-panel swap: remove the damaged assembly, transfer the cables, and mount the new unit. Take care with the display and touch connectors, keep screws sorted by length, and support the assembly by its edges while you work. If the frame is included, the whole front of the lid comes across in one piece. Quality and packaging Assemblies are sourced from established manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Stock: Out of Stock