HP PAVILION 15-CC laptop screens & parts

A replacement battery compatible with the HP PAVILION 15-CC SERIES, supplied new. If your machine shuts down early, reports a swollen or "service" battery, or only runs on mains power, a new battery is the fix — and on most modern laptops it is a straightforward one. Before you order Specifications — compare the voltage, capacity and battery part code printed on your original with this listing, and check the model label on the underside of your laptop against the models named in the title. Batteries are shaped for their series and do not carry across between them. Variations — where the listing offers more than one option (capacity or grade), choose the variation that corresponds to what your machine came with. Images — check the photos for the connector type and the outline of the battery; both need to correspond to your original. Unsure? — send us a photo of the label on your existing battery together with your HP 15-CC SERIES and we will confirm compatibility. Swollen battery? — stop using the laptop, do not press on the case or trackpad, and replace it promptly. A swollen battery only gets worse. Fitting and battery care Power off and unplug before opening the base. Disconnect the old battery's connector first, and reconnect the new one last. Give the new battery a full charge before its first run on battery power. Recycle the old one: in Australia, any B-cycle drop-off point (most major supermarkets have one) takes laptop batteries free of charge. Never put a lithium battery in the bin. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Part: Battery

Stock: Out of Stock

A replacement battery compatible with the HP PAVILION 15-CC SERIES, supplied new. If your machine shuts down early, reports a swollen or "service" battery, or only runs on mains power, a new battery is the fix — and on most modern laptops it is a straightforward one. Before you order Specifications — compare the voltage, capacity and battery part code printed on your original with this listing, and check the model label on the underside of your laptop against the models named in the title. Batteries are shaped for their series and do not carry across between them. Variations — where the listing offers more than one option (capacity or grade), choose the variation that corresponds to what your machine came with. Images — check the photos for the connector type and the outline of the battery; both need to correspond to your original. Unsure? — send us a photo of the label on your existing battery together with your HP 15-CC SERIES and we will confirm compatibility. Swollen battery? — stop using the laptop, do not press on the case or trackpad, and replace it promptly. A swollen battery only gets worse. Fitting and battery care Power off and unplug before opening the base. Disconnect the old battery's connector first, and reconnect the new one last. Give the new battery a full charge before its first run on battery power. Recycle the old one: in Australia, any B-cycle drop-off point (most major supermarkets have one) takes laptop batteries free of charge. Never put a lithium battery in the bin. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Part: Battery

Stock: Out of Stock

A replacement touch screen compatible with the HP PAVILION 15-CC005NA, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your HP 15-CC005NA and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the HP PAVILION 15-CC010NR, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your HP 15-CC010NR and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the HP PAVILION 15-CC020NR, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your HP 15-CC020NR and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the HP PAVILION 15-CC029NA, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your HP 15-CC029NA and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the HP PAVILION 15-CC033NA, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your HP 15-CC033NA and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the HP PAVILION 15-CC034NA, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your HP 15-CC034NA and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock

A replacement touch screen compatible with the HP PAVILION 15-CC076SA, built with the touch sensor embedded in the LCD cell itself. There is no separate glass digitizer: this panel is the complete touch surface for laptops built with an embedded (in-cell) touch design. Panel specifications Refresh rate 60Hz Before you order Touch laptops are built two ways, and the parts are not interchangeable, so please check the following against your machine: Touch construction — if your original is a bare panel with no glass bonded over the front, an embedded-touch screen like this one is the compatible type. If your machine has edge-to-edge glass glued over the LCD, you need a touch screen assembly instead. Specifications — compare the resolution, refresh rate and connector. The touch signal travels through the main screen cable, so the pin count and socket position must line up with your original. Variations and images — if the listing offers more than one option, pick the variation whose specifications suit your machine, and use the photos to check connector position and mounting points before you commit. Unsure which panel you have? — the code printed on the rear of your original panel settles it. Send it to us with your HP 15-CC076SA and we will check compatibility for you. Quality and packaging Panels are sourced from established LCD manufacturers, inspected before dispatch and shipped in rigid, foam-lined packaging designed for glass. Where a compatible-grade panel is supplied, it meets or exceeds the specification of the part it replaces; the panel maker can vary with stock. Fitting Fitting follows the same steps as a standard screen swap — unclip the bezel, unscrew the old panel, transfer the cable — with one extra caution: the connector also carries the touch signal, so seat it fully and squarely before first power-on. If touch does not respond after the swap, reseat the cable before assuming a fault. Warranty, returns and delivery Delivery: shipped Australia-wide with tracking. Returns: if a part arrives faulty or turns out not to be compatible with your machine, contact us first and we will make it right under our returns policy.

Refresh_rate: 60Hz

Stock: In Stock